Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Electric Gate Repair for Everett Homeowners
Electric gate acting up? When an operator stops reversing, a keypad stops accepting codes, or a slide gate halts halfway, every arrival and departure turns into a walk in the rain. We handle electric gate repair in Everett as a core specialty, not a sideline. Our technicians have up to experience and recognize model-level failure patterns across the operators most Everett properties run, from budget Mighty Mule units to FAAC and BFT commercial hardware. We diagnose the actual fault, tell you honestly whether repair or replacement makes sense, and quote the price before any work starts. Same-day service is often possible when you call early. Call (844) 834-1197 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Opener Repair
Gate Opener Repair covers the unit that actually moves your gate: the motor housing, the drive gear, the limit switches, and the arm or chain that pushes the leaf. You need it when the gate runs but won’t latch, grinds partway, reverses for no reason, or hums without moving at all. We work the opener you already own and trace the fault instead of selling a whole new system. Typical opener repairs in Everett run $180 to $340 for a mechanical fix such as a stripped gear, a failed limit switch or a worn drive arm, and $250 to $520 when the control board or receiver has to be replaced. The written estimate fixes the final price before we touch anything. We service Linear and Viking openers regularly, along with the other makes Everett properties run.
Common Opener Failure Points
On arm-style swing openers, the drive gear and the limit cams wear first, and the gate gradually over-travels or stalls against the stop. On slide operators, the chain or rack and the pinion gear take the wear, often showing up as jerky movement before a full stop. We check all of these in one visit so a small part failure doesn’t get mistaken for a dead motor.
When an Opener Is Worth Replacing
An opener with a cracked housing, a burnt winding or a board that’s no longer made is usually cheaper to replace than to chase. We’ll say so plainly when that’s the case. If the rest of the gate is sound, a new operator is a straightforward job and you keep the hardware you already trust.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Automatic Gate Repair
Automatic Gate Repair covers the whole system that opens and closes on its own: the operator, the safety devices, the wiring, and the control logic that ties them together. You need it when the gate moves on its own, stops mid-travel, fails to reopen for a vehicle, or ignores every remote in the house. We test the full chain rather than just the motor, because an automatic gate that behaves unpredictably is usually reporting a sensor or control fault, not a worn drive. Estimated automatic gate repair in Everett runs $180 to $340 for safety-device and sensor work, $250 to $520 for control-board or receiver replacement, and $350 to $750 when wiring, loop detectors or a combination of faults are involved. We work on swing, slide and barrier arm configurations, and the written estimate sets the final price before work begins.
Safety Devices and Photo Eyes
Photo eyes and safety edges are what stop a closing gate on a person or vehicle, so they’re the first thing we test on any automatic gate call. A misaligned or dirty eye can mimic a dead operator. When we find a failed safety device, we recommend fixing it, not bypassing it.
Erratic Behavior and Control Logic
A gate that opens a few feet and reverses, or runs only from inside the house, is usually reporting a receiver, board or wiring problem. We trace the signal path with a meter and a test remote instead of guessing. That’s how a return visit gets avoided.
Electric Gate Motor
The Electric Gate Motor is the engine of the system, and when it fails the gate simply stops. You need motor service when the gate is stuck, the motor overheats and cuts out, it strains under load, or you hear a loud hum with no movement. We test the motor under load, check the capacitors and windings, and separate a true motor failure from a gearbox, voltage or board problem before recommending anything. Estimated motor repair or replacement in Everett runs $280 to $560 for a residential motor swap where the mount and wiring are sound, and $450 to $900 when the gearbox, capacitor or mount also needs work. Commercial-grade motors sit at the upper end. We service Ghost Controls and Linear motors regularly. The written estimate sets the final price before we start.
Motor Symptoms to Watch
A hot motor housing after a single cycle, a grinding sound on start, or a gate that moves slower each month are all early signs. Catching them before a full failure usually means a cheaper repair. A motor that trips a breaker is a stop-and-call situation.
Motor Sizing and Load
An undersized motor on a heavy gate works harder every cycle and fails early, especially on a slope. When we replace a motor, we check the gate weight and the grade so the new unit is matched to the job. That prevents a repeat failure six months down the line.
Gate Access Control
Gate Access Control is the system that decides who gets in: keypads, card readers, remotes, intercoms, vehicle loop detectors and the receivers that talk to them. You need service when codes stop working, a remote opens a gate it shouldn’t, the intercom cuts out, or a keypad goes dead after a power flicker. We diagnose the access hardware and its wiring rather than replacing the whole panel, and we can reprogram or re-pair the system on the same visit when the hardware is healthy. Estimated access control repair in Everett runs $150 to $320 for keypad, receiver or remote work, and $300 to $650 for intercom, reader or loop-detector repairs that involve wiring. DoorKing entry systems are a regular part of our work. Everything is quoted and agreed before any work starts.
Keypads, Remotes and Receivers
Most access problems come down to a dead keypad, a receiver that’s lost its memory, or remotes that need re-pairing after a board swap. We test each device and re-pair what we can. Replacement is only recommended when the hardware has actually failed.
Intercoms and Entry Panels
A buzzing intercom or a panel that powers up but won’t release the gate usually points to a wiring or power fault behind the unit. We trace the run rather than swapping the panel first. On shared entrances, that often saves a property manager a bigger bill.
Commercial Gate Operator
A Commercial Gate Operator is the heavier-duty unit that runs an apartment entrance, an HOA gate, a business lot or a gated community, and it’s built for a far higher cycle count than a driveway unit. You need service when it starts skipping cycles, stops reversing, throws a fault code, or leaves vehicles queued at the entrance. We work on FAAC, BFT and DoorKing commercial operators and handle both the mechanical side and the access-control side of the system, which is where many general repair calls stall. Estimated commercial operator repair in Everett runs $350 to $900 depending on the unit and the fault, and the written estimate fixes the final price before any work starts. This is measured and scheduled work, not a same-day promise, because commercial parts often have to be matched to the model first.
High-Cycle Wear and Tear
Commercial operators run hundreds of cycles a day, so gears, brakes and limit systems wear faster than on a home gate. We inspect the full drive train and log what’s close to failing. That lets a property manager plan a repair instead of reacting to a stuck gate at a busy entrance.
Keeping Entrances Moving
A commercial gate that fails locks out residents, deliveries and tenants all at once. When a part is on order we can often get the gate to a safe manual position so the entrance still works. Safety devices are never bypassed to make that happen.
Brands We Service
We work on the brand you already own. LiftMaster operators are common on residential swing and slide gates, and we know their receiver and board failure patterns. FAAC and BFT units show up on commercial and heavier residential gates, where the drive train and control logic are the usual suspects. Linear and Viking openers have their own wear points in the gears and limit switches, and we service both regularly. Ghost Controls is a frequent sight on newer residential installs, and we’re familiar with its control behavior.
DoorKing handles a lot of the access-control and entry-panel work on shared and commercial entrances, and we diagnose those systems down to the reader and wiring. Elite units round out the mix on residential driveways. Repair or replace, we’ll tell you which one actually makes sense for the unit you have. Whether you have DoorKing or any other make, we can help. We’re independent and experienced with these brands, not tied to any one of them.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate reverses for no reason. A gate that opens then closes again on its own is usually reporting a safety-device or board fault. That behavior can trap a vehicle or a person, so it’s worth a call before it gets worse.
- The motor hums but the gate doesn’t move. A hum with no travel points to a seized gearbox, a failed capacitor or a jammed drive. Running it this way can burn out a motor that was repairable.
- The gate drifts open or won’t stay closed. A gate that creeps open on its own is an access and security problem at the same time. It’s often a limit switch, a brake or a control logic fault that a technician can pin down quickly.
- Keypad codes or remotes stop working. When access hardware fails, you’re locked out of your own gate or letting in people you shouldn’t. A receiver or keypad fault is usually a fast fix once it’s diagnosed.
- You hear grinding, scraping or a new rattle. New noises mean metal is wearing against metal somewhere in the drive. Catching it early keeps a small part replacement from turning into a motor or gearbox job.
Our Process, Step by Step
- 1
Call and describe the symptom. Tell us what the gate is doing and which brand the operator is. That first conversation often narrows the fault before we arrive, and we’ll book a visit that fits. Call (844) 834-1197. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
- 2
On-site diagnosis. We test the operator, the safety devices, the access hardware and the wiring with a meter and a test remote. We separate the actual fault from the symptom so we’re not replacing parts that are still good.
- 3
Written estimate before any work. You get the price in writing, with the parts and labor broken out. Nothing starts until you agree to it. If repair isn’t the right call, we’ll tell you that too.
- 4
The repair itself. We fit the parts, re-pair remotes and keypads, and re-test every safety device before we leave. The gate should cycle cleanly and reverse on command when we’re done.
- 5
A walkthrough and a clear record. We show you what failed, what we did, and what to watch going forward. If a bigger job like a full new installation is coming, you’ll know before it becomes urgent.
How Much Does Electric Gate Repair Cost in Everett?
Electric gate repair in Everett typically runs $180 to $340 for common mechanical and sensor fixes, and $250 to $900 for board, motor, access-control and commercial work, depending on the unit and the fault. A typical opener repair in Everett runs $180 to $340 depending on the part that failed. A motor or gearbox job typically runs $280 to $560 for a residential unit. Access-control repairs usually run $150 to $320 for keypad, receiver and remote work. Commercial operator repairs run $350 to $900 because the units are heavier and parts have to match the model.
What affects the price: the brand and model of operator, whether the fault is mechanical or electrical, how accessible the wiring is, and whether the gate itself also needs adjustment. A gate that’s out of level or dragging will wear out a new part fast, so we factor that in.
How to avoid overpaying: get a written estimate before work starts, and be wary of anyone who recommends a full replacement without testing the motor and the safety devices first. Our estimate is free, and the written price is the price. It sets the final cost with no surprises added after the fact.
What’s included in a free estimate: a full diagnosis of the operator, safety devices, access hardware and wiring, a clear explanation of what failed, and a written price for the repair or the replacement, whichever actually makes sense. Call (844) 834-1197 for an exact quote, estimates are free.
Our Service Area Near Everett
We provide gate repair in Everett and the surrounding communities, including Eastmont, Mukilteo, Mill Creek, Silver Firs, Martha Lake, Lake Stickney and North Lynnwood, plus Snohomish to the east. Dispatch runs from 7am to 7pm, Sunday through Friday, and most nearby calls are scheduled the same day when you reach us early. Our technicians have up to experience with the operators these neighborhoods run. Call (844) 834-1197 to book.
Serving Everett, WA – Our Local Coverage Area
We serve Everett and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Electric Gate Repair in Everett
Electric gate repair is the diagnosis and fixing of the powered parts of an automatic gate: the motor and operator, the control board, the safety devices, the access hardware and the wiring that connects them. It’s different from fixing the gate leaf or hinges, because the fault is usually in the system that moves and controls it. We test the whole chain so the repair targets the actual failure. Call (844) 834-1197 for a free estimate.
Most electric gate repairs in Everett take one to three hours on site once we’ve diagnosed the fault. A keypad, remote or sensor fix is often under an hour. A motor or gearbox replacement can take longer, and a commercial operator with parts on order may need a return visit. We give you a realistic time frame with the written estimate before work begins. Call for an exact quote.
Electric gate repair in Everett typically runs $180 to $340 for mechanical and sensor fixes, and $250 to $900 for board, motor, access-control and commercial work. The exact price depends on the brand, the fault and whether parts need ordering. Every job is quoted in writing and agreed before work starts, and the estimate is free. Call (844) 834-1197 for your exact price.
Yes, we service DoorKing and Ghost Controls systems, along with LiftMaster, FAAC, BFT, Linear, Viking, Elite and Mighty Mule. We work the brand you already own and know where each one tends to wear out. Whether the fault is in the operator, the board or the access hardware, we diagnose it before recommending anything. Call (844) 834-1197 to book a visit.
Same-day service is often possible in Everett when you call early. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. This applies to repair work; new installations and commercial operators are measured and scheduled. Call (844) 834-1197 to check availability.
We stand behind the work and the parts we fit. The exact warranty terms depend on the repair and the parts used, and we confirm them with you in writing before work starts so there’s no ambiguity after. You’ll know what’s covered and for how long. Call (844) 834-1197 if you have a question about a specific repair.
Clear the area on both sides of the gate and make sure we can reach the operator, the control panel and the keypad. Note which remotes or codes have stopped working and when the problem started. If the gate is stuck open or closed, leave it where it is rather than forcing it. That’s all we need to get started. Call (844) 834-1197 to schedule.
Schedule Your Electric Gate Repair Service in Everett Today
Don’t let a gate that won’t open or close throw off your whole day. Call (844) 834-1197 to book electric gate repair in Everett, and we’ll get you back to secure in one visit. Our technicians have up to experience, the estimate is free, and the price is quoted in writing before any work starts. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Everett.