Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Everett?
Gate access control in Everett typically costs $350 to $1,200 for a keypad, card reader, or intercom setup on an existing gate, and $1,800 to $4,500 when new wiring and an operator are part of the job. A single keypad swap or remote receiver replacement usually lands at the low end; a full multi-tenant entry system for a commercial gate sits at the top. The written estimate sets the final price, and we give that estimate free.
Most calls we get about access control start the same way: the gate opens, but not for the people it should. Maybe the keypad has gone dead, maybe the fob works from the driveway and not from the street, or maybe the entry system at a small commercial lot has started letting everyone in. That’s a diagnosis problem before it’s a parts problem, and the price depends on which piece of the system has failed.
Gate Access Control Cost Breakdown (2026)
Here’s what the work typically runs in the Everett market. Every number below is an estimated range for the job, not a quote.
| Access Control Item | Typical Estimated Range |
|---|---|
| Keypad replacement (standalone, existing wiring) | $350 – $650 |
| Keypad with new wiring run to the gate | $650 – $1,300 |
| Remote receiver and fob programming | $200 – $450 |
| Card reader or proximity reader (single door or gate) | $700 – $1,600 |
| Telephone entry intercom with directory | $1,100 – $2,400 |
| Vehicle loop detector and safety loop install | $600 – $1,400 |
| Control board replacement (LiftMaster, FAAC, BFT, DoorKing, Linear) | $450 – $1,100 |
| Full access control package with new operator (residential) | $1,800 – $4,500 |
| Commercial multi-tenant entry system | $2,500 – $7,000+ |
| Diagnostic visit and written estimate | Free |
What pushes a job toward the top of these ranges is almost always wiring, not hardware. A keypad swap on an existing circuit is a short visit. Pulling new wire across a driveway, under a walkway, or out to a slide gate at the back of a lot takes time and trenching, and that labor is what separates a $400 job from a $1,300 one. On the operator side, a control board for a commercial DoorKing unit costs more than a board for a residential Mighty Mule, and that difference shows up in the estimate.
What keeps a job at the low end is a clean existing install. If the gate already has power at the post, a working operator, and wiring that hasn’t been chewed through or waterlogged, adding or replacing access control is straightforward. Our technicians have up to experience across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we recognize model-level failure patterns instead of guessing at them.
What Affects Gate Access Control Pricing in Everett
Everett is a wet, cool climate with a lot of older housing stock and a mix of new commercial build-outs, and both shape what access control work costs here.
- Wiring runs and trenching. This is the biggest swing. A gate on a short driveway with power already at the post is quick. A gate 80 feet from the nearest power source needs a new run, and the cost reflects the digging and conduit, not the reader.
- Wet-weather exposure. Everett gets long stretches of rain through the fall and winter, and outdoor keypads and readers take that moisture. Water intrusion into a keypad or control enclosure is one of the most common failure points we see, and a properly sealed enclosure or pedestal adds cost up front but saves repeat visits.
- Operator brand and age. Access control talks to the operator, so the two have to match. A newer LiftMaster or FAAC operator will accept most modern readers and receivers. An older unit may need a compatible interface or a board replacement to work with a new entry system, and that’s a real line item.
- Residential versus commercial. A homeowner adding a keypad to a swing gate is a different job than an HOA contact managing a shared entrance with a directory, vehicle loops, and multiple tenants. Commercial systems carry more hardware, more wiring, and more configuration.
- Gate type: swing, slide, or barrier arm. Slide gates often need safety loops and more careful sensor placement. Barrier arms typically need a loop detector at minimum. Each configuration has its own access control layout.
- Whether the failure is control or mechanical. Sometimes the keypad is fine and the gate isn’t moving because of a motor or arm issue. We diagnose electrical, mechanical, and control-board failures together so you’re not paying for a reader when the problem is the operator.
How to Save on Gate Access Control
The cheapest access control job is the one where the diagnosis is right the first time. A few things help:
- Get the whole system looked at, not just the part that failed. A dead keypad and a failing control board can present the same way. A single diagnostic visit that checks the operator, wiring, and reader together usually costs less than two separate service calls chasing the wrong component.
- Fix it before it fails completely. A keypad that works only when you press hard, or a reader that works in dry weather and not in the rain, is telling you something. Water intrusion and worn contacts get worse, and a small repair now usually beats a full replacement later.
- Ask whether repair or replacement makes sense. We’ll tell you which one actually makes sense for your gate. If the operator is sound and only the entry hardware is failing, you don’t need a new gate system. If the operator is on its last legs, putting a new reader on it may not be worth it.
- Match the hardware to how the gate is actually used. A single-family driveway doesn’t need the same entry system as a 12-unit lot. Specifying the right level the first time avoids paying for capability you won’t use.
- Take the free estimate. Call (844) 834-1197 and we’ll come out, diagnose the system, and give you a written estimate at no charge. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Repair or Replace: Which Makes Sense for Your Gate?
If the access control hardware has failed but the operator and gate are solid, repair is almost always the answer. A new keypad, reader, or receiver on a healthy system costs a fraction of a full replacement. If the control board is gone and the operator is old, or if the gate itself is struggling mechanically, the math changes. We diagnose before we recommend, and we’ll tell you plainly which direction fits your gate rather than defaulting to a full swap. For the broader picture on getting a gate working again, see gate repair Everett.
Why Brand Familiarity Keeps Access Control Costs Down
Access control is where gate systems get brand-specific fast. A DoorKing entry system, a FAAC operator, a LiftMaster receiver, and a Ghost Controls residential unit each have their own wiring conventions and failure patterns. When a technician already knows the model, the diagnosis is quicker and there are fewer return visits. We work across nine major brands, from budget-friendly Mighty Mule and Ghost Controls units to high-end FAAC and BFT commercial operators, and we work on the brand you already own rather than steering you toward a replacement.
That range matters for property managers and HOA contacts as much as for homeowners. A small commercial entrance with a mixed hardware footprint doesn’t have to be a puzzle. We cover residential and light-commercial systems, swing, slide, and barrier arm, and the goal is to get you back to secure in one visit where the diagnosis allows it. If you’re in the Everett area and your electric gate is acting up, that’s the call to make.
FAQs – Gate Access Control Cost
How much does a keypad for a gate cost in Everett?
A gate keypad in Everett typically runs $350 to $650 installed when the existing wiring can be reused, and $650 to $1,300 when a new wire run is needed. The hardware itself is the smaller part of that range; the wiring and labor are what move the number. Call (844) 834-1197 for an exact quote, and the estimate is free.
Is it cheaper to repair or replace my gate access control?
Repair is usually cheaper when the operator and gate are healthy, often $200 to $1,100 for the failed component versus $1,800 to $4,500 for a full package with a new operator. Replacement makes more sense when the operator is old and the control board is gone. We’ll tell you which one actually makes sense after we look at it. Call (844) 834-1197 to set up the free estimate.
Can you come out today for a gate access control problem?
Same-day service is often possible. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (844) 834-1197 and we’ll get you on the schedule.
How much does a commercial gate entry system cost in Everett?
A commercial multi-tenant entry system in Everett typically runs $2,500 to $7,000 or more, depending on the number of readers, directory hardware, vehicle loops, and how far the wiring has to run. Telephone entry intercoms alone land around $1,100 to $2,400. Call (844) 834-1197 for a written estimate on your specific entrance.
Why does my gate keypad stop working in the rain?
Water intrusion into the keypad or its enclosure is a common cause, and it’s one of the failure points we see most in this climate. A properly sealed enclosure or a replacement keypad with better weather protection typically runs $350 to $650, more if new wiring is needed. Call (844) 834-1197 and we’ll diagnose whether it’s the keypad, the wiring, or the control board.
Get a Free Gate Access Control Estimate in Everett
If your keypad has gone dead, your reader is unreliable, or your entry system needs a fresh look, we’ll come out, diagnose it, and give you a written estimate at no charge. We work on the brand you already own, from Ghost Controls to FAAC, and we’ll tell you whether repair or replacement actually makes sense. Call (844) 834-1197 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Everett market as of 2026. Gate Repair Everett offers free estimates – call (844) 834-1197.
Written by the team at Gate Repair Everett.
What Our Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Whitney Sutton"Repair is holding. He was quite a bit later than the window I was given, and nobody called me about it, I had to call them. The work itself was done well once he got here."
- Luis Salazar"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Paige Brooks