Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Everett?
Gate installation in Everett typically runs $2,800 to $9,500 for a full project, with most residential swing or slide gate installs landing between $3,500 and $6,800. A basic manual gate with new posts and hardware sits at the low end, around $2,800 to $4,200, while an automated system with an operator, safety sensors, and access control pushes the total toward $6,000 and up. Commercial barrier arms and heavy-duty slide gates can exceed $12,000 once wiring, concrete, and controllers are included.
Those are estimated ranges for the Everett market in 2026. The written estimate we provide after looking at your property sets the final price, and the estimate itself is free.
Key Takeaways
- Typical Everett gate installation: $2,800 to $9,500, depending on gate type, operator, and site conditions.
- The gate hardware is usually the smaller part of the bill. Posts, footings, trenching, and power are where budgets move.
- Automated gates cost more upfront but are what most homeowners in Everett actually want for access control.
- Our technicians have up to experience across swing, slide, and barrier arm systems.
- Free estimates, upfront pricing, and a clear repair-or-replace recommendation before any work starts.
Gate Installation Cost Breakdown (2026)
Here’s how a gate installation project breaks down line by line. Use this table to see where your money goes before you call. All figures are typical estimates for the Everett area.
| Line Item | Estimated Cost Range | Notes |
|---|---|---|
| Manual swing gate (single leaf, up to 12 ft) | $2,800 – $4,200 | Gate panel, posts, hinges, latch, concrete footings |
| Manual slide gate (up to 16 ft) | $3,200 – $5,000 | Track, rollers, posts, ground prep |
| Dual swing gate (driveway width) | $4,500 – $7,200 | Two leaves, center latch, heavier posts |
| Swing gate operator (residential) | $1,400 – $2,800 | Includes arm or underground operator, control board |
| Slide gate operator (residential) | $1,600 – $3,200 | Includes motor, rack, and control enclosure |
| Safety sensors and photo eyes | $250 – $550 | Required for automated gates; prevents crush injuries |
| Keypad or access control entry | $350 – $1,200 | DoorKing, LiftMaster, and Linear units common in Everett |
| Wiring and power run | $600 – $2,500 | Varies with distance from panel and trenching needed |
| Concrete footings and site prep | $500 – $1,800 | Depends on soil, slope, and existing surface |
| Commercial barrier arm system | $6,500 – $12,000+ | Includes operator, arm, loop detectors, controller |
The gate itself is often less expensive than everything around it. Getting power from the house or panel to the gate line, cutting and pouring footings, and running conduit under a driveway are the items that can swing a project by a couple thousand dollars. On a flat lot with power already close to the fence line, installation stays near the bottom of these ranges. On a sloped driveway with a long power run, expect the higher end.
What Affects Gate Installation Pricing in Everett
Everett sits on a mix of flat lots near the waterfront and sloped properties on the hillsides above the Snohomish River valley. That geography shapes gate projects more than most homeowners expect. Here’s what we look at when we price a job.
- Driveway slope and grade. A sloped driveway needs either an underground swing operator or a slide gate with a level track, and both cost more to engineer and install than a flat-lot setup. Everett’s hillside neighborhoods see this often, and it’s one reason two gates of the same size can price $1,500 apart.
- Power availability. If there’s no outlet or circuit near the gate line, a new run from the panel adds cost. Some properties need a dedicated circuit, and one property owner may need an electrician to set that up before we start. Discussing this in the estimate keeps surprises out of the final bill.
- Gate material and weight. Aluminum stays the lightest and most affordable choice for automated gates. Ornamental steel, wood, and composite weigh more, which means heavier operators, larger footings, and higher cost.
- Operator brand and features. A Mighty Mule or Ghost Controls residential operator keeps cost down. A commercial-grade FAAC or BFT unit, or a DoorKing access control system for an HOA or small commercial entrance, adds cost but handles daily traffic and duty cycles the residential units can’t.
- Permits and site rules. Most cities require a permit for a gate with an electrical operator, and some have setback or fence height rules near a corner or driveway. We recommend asking the city of Everett building department about permit requirements for your address. Those fees are set by the city, not us, and we won’t guess at them.
- Wet-season ground conditions. Western Washington rain means footings need to be set below the frost-affected zone and drained properly. Doing that work right the first time adds a little to the install and saves a lot on repairs later. Posts go to the proper footing depth, period.
Why Gate Installation in Everett Isn’t a Handyman Job
A gate looks simple until you add an operator. Once an automated gate is installed, you have a machine that can crush, pinch, or trap. That’s why automated gate installation belongs with a team that works on gates every day, not a general contractor who adds it to a list of projects.
Our work is limited to gate repair, electric gate repair, and gate installation. We don’t split our attention between gates, fencing, and garage doors. The gate brands we know well – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – cover nearly every operator a homeowner in Everett is likely to own or want installed. We work on the brand you already own and install the brand that fits your property.
That brand fluency matters most when an electric gate acts up. Control boards fail, sensors get misaligned, batteries in solar units die, and actuators wear out. Recognizing the failure pattern on the model you have means we can diagnose it faster and often fix it in one visit instead of guessing and ordering parts on a return trip.
Cost to Add Automation to an Existing Gate
The gate is already there and works by hand. What does it cost to automate it? Retrofitting an operator onto an existing manual gate in Everett usually runs $1,900 to $4,800, including the operator, safety sensors, control box, and wiring.
Not every existing gate can take an operator cleanly. We check the gate’s weight, balance, hinge condition, and post stability first. A gate that sags or swings loose needs repair before an operator goes on, or the motor works harder than it should and wears out early. Our job is to tell you honestly whether your gate is a good candidate for automation or whether it needs structural work first.
Manual vs. Automated: What the Numbers Look Like
- Manual swing gate install: $2,800 – $4,200 typical. No power, no sensors, no controller.
- Automated swing gate install: $4,500 – $7,500 typical. Adds operator, sensors, access control, and wiring.
- Automated slide gate install: $5,000 – $9,500 typical. Track, motor, and level footing required.
The gap between manual and automated is real money, but so is the difference in daily use. A gate you have to get out of the car to open is a gate you might stop using. Automation solves that.
How to Save on Gate Installation
Nobody likes paying more than they need to. Here’s how homeowners in Everett keep a gate project under control.
- Choose the right operator for your traffic. A residential-grade unit is fine for a driveway used a few times a day. Spending extra on a commercial-grade FAAC or BFT operator when a Mighty Mule will do is money you don’t need to spend. We’ll match the operator to how you actually use the gate.
- Locate the gate where power is close. If you have flexibility on where the gate goes, putting it near an existing power source can save several hundred dollars in wiring and trenching.
- Keep the gate light. Aluminum frames cost less to automate because the operator and footings do less work.
- Replace when repair no longer pays. If your existing gate post is sound, automate it instead of replacing it. Retrofitting often costs less than a fresh install.
- Get the free estimate. A written estimate lets you compare options side by side rather than guessing. Call (844) 834-1197 and we’ll come look at the property, measure, and put the numbers in writing.
Repair or Replace: Which Makes Sense for Your Gate?
If your electric gate won’t open, the first question is whether it needs a repair or a replacement. Repair is almost always cheaper, and often it’s the right answer. A dead operator with a bad control board is a repair, not a reason to install a new gate.
Replacement starts to make sense when the gate structure itself is failing – rusted-through posts, a frame that’s cracked or bent beyond safe use, or a manual gate that can’t take an operator and never will. When that’s the case, a fresh install is the more economical path over a few years. We work on both repair and installation, so the recommendation isn’t tied to selling you a new gate. Repair or replace, we’ll tell you which one actually makes sense.
If a gate fails and you need help, call us. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Residential and Commercial Gate Installation in Everett
Homeowners, small commercial property managers, and HOA contacts all call about the same problem: a gate that controls access and won’t stay working. Our installation work covers both sides.
For homeowners, the typical project is a driveway gate with an operator that opens from the car. For small commercial properties and HOA entrances, the typical project is a slide gate or barrier arm with access control hardware, loop detectors, and a controller that logs entry. DoorKing and LiftMaster lead the way in commercial access control, and we know those systems well enough to install them correctly and keep them working.
What Happens When You Call
When you call, we ask a few questions about the gate, the site, and how you want to use it. Then we set up a time to look at the property and give you a written estimate. That estimate is free, the pricing is upfront, and the estimate sets the final price. When we’re done, the goal is simple: a gate that works and a property that’s back to secure.
If your gate has failed or you’re planning a new install in the Everett area, get in touch. You can read more about our gate repair Everett service if your gate needs fixing first, and you can find our local coverage on the Everett page.
FAQs – Gate Installation Cost
How much does gate installation cost in Everett?
Gate installation in Everett typically costs $2,800 to $9,500, with most residential projects landing between $3,500 and $6,800. A manual gate sits at the lower end, around $2,800 to $4,200, and an automated gate with operator, safety sensors, and access control pushes toward $6,000 and higher. Call (844) 834-1197 for an exact quote. Estimates are free.
Is it cheaper to repair or replace an electric gate?
Repair is usually cheaper, often by a wide margin. A control board, sensor, or actuator replacement typically runs $250 to $1,200, while a full automated install runs $4,500 and up. Replacement makes sense when the gate structure is failing, not just the operator. Call (844) 834-1197 and we’ll tell you which one applies to your gate.
Does gate installation require a permit in Everett?
Most cities, including Everett, require a permit for a gate with an electrical operator, and it’s best to confirm the requirements for your exact address with the city of Everett building department before work starts. Permit fees are set by the city and are not part of our installation price. Call (844) 834-1197 with questions about how a permit affects your project timeline.
Can you install a solar-powered gate operator in Everett?
Yes. Solar operators make sense in Everett when the gate is far from a power source and trenching would be expensive. A solar setup typically adds $400 to $1,200 over a wired operator, depending on panel size and battery capacity. Call (844) 834-1197 and we’ll help you decide if solar is the right call for your property.
What’s the cheapest type of automatic gate to install in Everett?
A single-leaf residential swing gate with a Mighty Mule or Ghost Controls operator is the lowest-cost automatic option, typically $4,000 to $5,500 installed. Slide gates and dual swing gates cost more because they need heavier hardware and larger footings. Call (844) 834-1197 for a free estimate on your specific project.
Can you come out the same day?
Same-day service is often possible when a gate has failed and needs repair. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (844) 834-1197 to get on the schedule.
Gate Repair Everett – Free Estimates on New Gate Installs
Whether you’re replacing a failing gate, automating a manual one, or installing a new access-controlled entrance, we can help you get the numbers straight before you commit. Our technicians have up to experience across swing, slide, and barrier arm systems, and we work with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The estimate is free, the pricing is upfront, and the final price is set by the written estimate.
Call (844) 834-1197. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If a gate fails on a Saturday, call and we’ll book you for Sunday.
Written by the team at Gate Repair Everett.
Pricing reflects the Everett market as of 2026. Gate Repair Everett offers free estimates – call (844) 834-1197.
What Our Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Whitney Sutton"Repair is holding. He was quite a bit later than the window I was given, and nobody called me about it, I had to call them. The work itself was done well once he got here."
- Luis Salazar"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Paige Brooks