Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Everett Homeowners
An automatic gate that won’t open leaves you parking on the street and worrying about who can walk up your drive. That stuck-open or stuck-closed gate is exactly what we handle. Gate Repair Everett works on the operator brands you already own, from Linear and Viking to DoorKing, and our technicians have up to experience diagnosing electrical, mechanical, and control-board failures rather than selling you a replacement you don’t need. We serve homeowners and property managers across Everett, WA, and same-day service is often possible when you call early. Repair or replace? We’ll tell you which one actually makes sense. Call (844) 834-1197. We answer 24/7.
Driveway Gate Repair
Driveway Gate Repair is the work of getting your residential swing or slide gate moving and latching correctly again, and it’s the call we take most in Everett. You need it when the gate drifts, reverses halfway, drags on the ground, or the remote stops responding, all of which usually trace back to a worn hinge, a misaligned track, a binding roller, or a failing actuator rather than the whole system. We test the operator and the gate separately, so we know whether the problem lives in the hardware or the controls. Typical driveway gate repair in Everett runs $200 to $600 depending on the fault, and the written estimate you approve before any work starts sets the final price. From Ghost Controls residential units to heavier commercial-grade arms, we work on the machinery you already have.
Gate That Drags or Binds
A gate that scrapes the ground or fights its own hinges puts constant strain on the motor until the operator fails too. We check hinge wear, post plumb, and roller contact to find where the bind starts. Fixing the mechanical drag early is what keeps the actuator alive.
Remote and Keypad Failures
When the remote quits but the wall switch still works, the gate is usually fine and the problem is the receiver or the remote itself. We test signal reception and re-pair or replace the control components as needed. Getting the entry control working again is often a quick visit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural repair work that restores a cracked frame, a broken hinge mount, or a sagging joint, and it’s what keeps a heavy gate hanging square instead of grinding itself apart. You need it after impact damage, when a weld has fatigued over years of swinging, or when a post bracket has pulled loose and the whole leaf drops. We assess whether the weld is the whole fix or a symptom of a deeper alignment problem, then repair the metal and re-hang the gate so it swings or slides true again. Gate welding in Everett typically runs $150 to $450 depending on the extent of the repair and how much realignment is involved, with the written estimate fixing the price before work begins. We don’t stop at the bead: a weld that isn’t followed by a proper alignment check just fails again.
Structural Cracks and Breaks
A crack in a gate frame spreads under the repeated load of every open and close. We grind out the failure, weld it properly, and check the surrounding joints while we’re there. Leaving a crack alone risks the leaf folding under its own weight.
Hinge and Bracket Repair
Hinges and post brackets carry the entire weight of the gate, and they’re where most weld failures start. We rebuild the mount and confirm the gate hangs level after the repair. A solid hinge mount is what stops the same weld from breaking twice.
Commercial Gate Repair
Commercial Gate Repair covers the access-controlled entrances at apartment complexes, storage facilities, and business lots, where a failed operator means lost revenue and frustrated tenants. You need it when a barrier arm won’t lift, a slide gate jams during peak traffic, or the access control stops recognizing cards and codes, and those failures need a faster response than a residential driveway gate. We diagnose the operator, the circuit board, the loop and safety sensors, and the access hardware as one system, so a failing reader doesn’t get mistaken for a dead motor. Commercial gate repair in Everett typically runs $300 to $900 depending on the system and the fault, and the written estimate is agreed before any work starts. From DoorKing access control to heavy FAAC and BFT operators, we’re fluent in the hardware commercial properties actually run.
Barrier Arms and High-Traffic Operators
Barrier arms take a beating at any busy entrance, and the actuator behind them wears faster than a residential unit ever will. We check the arm mechanism, the gearbox, and the limit settings to find what’s causing the stall. High-cycle operators need their mechanical wear addressed before the motor burns out.
Access Control Diagnostics
When cards and codes stop working, the gate hardware is often fine and the fault is in the reader, the controller, or the wiring between them. We trace the signal path rather than guessing at parts. Restoring reliable access control keeps traffic moving and keeps unauthorized entries out.
Iron Gate Repair
Iron Gate Repair keeps a heavy metal gate swinging smoothly and locking securely, and it’s the work that prevents a small hinge or alignment issue from turning into a bent frame. You need it when an iron gate sags, drags, won’t latch, or the operator struggles to move a leaf that’s gotten heavier to swing over time. Iron and steel gates carry real weight, so a worn hinge or a slightly settled post translates into real strain on both the hardware and the actuator. We check the hinges, the alignment, the latch, and the operator together, then repair what’s actually failing instead of replacing the whole gate. Iron gate repair in Everett typically runs $200 to $550 depending on the fault and the gate’s condition, and the price is set by the written estimate before any work starts.
Sagging and Misalignment
An iron gate that sags is usually telling you a hinge has worn or a post has shifted. We measure the alignment and correct the cause so the gate hangs true again. Left alone, a sagging gate puts uneven load on the operator until that fails too.
Latch and Lock Repair
A gate that won’t latch is a security problem as much as a mechanical one. We repair or replace the latch hardware and confirm it engages cleanly every cycle. A reliable latch is what makes the gate actually secure when it’s closed.
Sliding Gate Repair
Sliding Gate Repair gets a gate that has jumped its track, lost its rollers, or stopped sliding back on the rails, and it’s the fix for one of the most common automated gate failures we see. You need it when the gate grinds along the ground, veers off the track, moves in jerks, or the operator runs but the gate barely travels. The usual culprits are worn rollers, a track that’s collected debris or shifted, a bent rail, or an actuator that’s lost its limit settings. We clear and inspect the track, replace worn rollers, realign the rails, and reset the operator so the gate glides through its full travel again. Sliding gate repair in Everett typically runs $200 to $600 depending on what’s worn and whether the track needs realignment, with the written estimate setting the final price.
Track and Roller Wear
Rollers and track are where a slide gate lives or dies, and both wear faster than most people expect. We replace worn rollers and true up the track so the gate rolls without binding. Smooth travel is what keeps the operator from overworking.
Operator Limit Settings
When the gate overshoots or stops short, the limit settings on the operator are usually out of adjustment. We reset them so the gate opens and closes fully every cycle. Correct limits protect both the gate and the motor from needless strain.
Wrought Iron Gate Repair
Wrought Iron Gate Repair restores the decorative ironwork and the mechanical function of a gate that’s both an entrance and a piece of the property’s look. You need it when the gate sags, a joint or ornament has loosened, the finish has worn to bare metal, or the gate no longer swings or latches the way it should. Wrought iron carries a lot of weight for its look, so worn hinges and settled posts show up as drag and misalignment long before anything visibly breaks. We repair the mechanical faults, tighten and re-secure loose joints, and treat the finish where wear has exposed the metal. Wrought iron gate repair in Everett typically runs $250 to $600 depending on the condition and the amount of finish work, and the written estimate sets the price before work begins.
Finish and Weathering
Bare metal on a wrought iron gate is where rust starts and where the gate starts to weaken. We address the worn finish and re-protect the exposed areas. Keeping the coating intact is what protects the structure underneath.
Loose Joints and Ornaments
Decorative joints and finials work loose over years of swing and vibration. We re-secure them so the gate stays solid and looks right. A gate that rattles apart is one that’s telling you to tighten things up now.
Metal Gate Repair
Metal Gate Repair covers the steel, aluminum, and mixed-metal gates that don’t fall neatly into one material category, and it’s the diagnostic work of figuring out why a metal gate has started to fight its operator. You need it when the gate binds, the frame has bent, a hinge or weld has cracked, or the gate simply won’t open and close smoothly anymore. Metal gates vary widely in weight and construction, so the fix depends on how the specific gate is built and where the stress is landing. We inspect the frame, hinges, track or swing path, and the operator as a system, then repair the actual cause. Metal gate repair in Everett typically runs $200 to $550 depending on the fault and the gate’s build, with the price confirmed in writing before any work starts.
Bent Frames and Impact Damage
A bent frame throws the whole gate out of alignment and strains every part of the system. We straighten or repair the frame and re-check the swing or slide path. Impact damage caught early is far cheaper to correct than a frame that’s bent the hinges with it.
Hinge and Roller Service
Hinges and rollers are the parts that take the load every single cycle. We replace worn hardware and confirm the gate moves smoothly afterward. Fresh, correct hardware is what takes the strain off the motor.
Wood Gate Repair
Wood Gate Repair addresses the sagging, sticking, and warping that wood gates develop as they age and as the seasons move the material around. You need it when the gate swells and sticks in damp weather, drops at the latch side, a hinge has torn loose, or the operator struggles to move a gate that’s gotten heavier and less square. Wood moves with moisture and temperature, so a gate that fits in summer can bind in winter, and hinges carry the extra load until they tear out. We repair the frame, re-hang the gate, replace failed hinges, and adjust the operator to match, then treat the wood where it needs protection. Wood gate repair in Everett typically runs $150 to $500 depending on the extent of the repair, with the written estimate setting the final price.
Swelling and Sticking
Wood that swells with moisture is the most common reason a wood gate starts to stick. We diagnose whether it’s a small adjustment or a deeper alignment issue. Correcting the cause stops the gate from fighting the operator.
Hinge Replacement
Wood hinges tear out when the gate is too heavy or the mounting has weakened. We reinforce the mount and replace failed hinges properly. A solid hinge on sound wood is what keeps the gate hanging straight.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the brand you already own, and that matters because every operator has its own failure patterns. Linear and Viking residential units are common on Everett driveway gates, and we know where their gearboxes and limit switches tend to wear. DoorKing commercial access control turns up on gated properties and HOA entrances, and we’re familiar with how those controllers and readers fail. Ghost Controls units are popular on residential installs, and we understand their control behavior well enough to diagnose problems quickly instead of guessing.
Brand-specific experience shortens the diagnostic path, so we spend less time chasing the wrong part and more time fixing the actual fault. Whether you have Linear, Viking, DoorKing, or any other make, we can help, and we’ll tell you honestly whether the fix is a repair or a replacement.
Signs You Need a Pro Right Now
- The gate stops mid-travel or reverses on its own. This usually points to a failing limit setting, a worn safety sensor, or a control-board fault. It won’t fix itself, and running the operator through it repeatedly can burn out the motor.
- The gate drags, grinds, or binds. A gate that fights its own path is loading the operator with strain every cycle. That wear compounds until a hinge, roller, or the actuator itself gives out.
- The operator hums but the gate doesn’t move. A humming motor with no movement signals a mechanical jam or a stripped gear rather than an electrical fault. Continuing to try it can turn a repair into a replacement.
- Remotes or keypads work only some of the time. Intermittent entry control is often a failing receiver, wiring, or reader. It’s also a security concern, since unreliable control means unreliable access.
- The gate sags, won’t latch, or swung into something. Alignment, hinge, or frame damage puts the whole system out of balance. The sooner it’s assessed, the smaller the repair usually is.
Our Process, Step by Step
- 1
You call, we listen. We ask what the gate is doing, what brand the operator is, and whether it’s a swing, slide, or barrier system. That first conversation tells us a lot and helps us arrive prepared.
- 2
On-site diagnosis. We test the operator and the gate separately, checking the motor, circuit board, sensors, access control, and the mechanical hardware. That separation is how we find whether the fault is electrical or mechanical.
- 3
A written estimate before work starts. You get a clear price for the repair, agreed in advance. We tell you honestly whether a repair makes sense or whether a replacement is the better call.
- 4
The repair itself. We fix the actual cause, not just the symptom, and confirm the gate cycles fully before we consider it done. Parts are matched to the system you have.
- 5
A final check with you. We walk the gate through a full open and close, confirm the latches and controls work, and answer your questions. Back to secure in one visit wherever the parts allow.
How Much Does Gate Repair Cost in Everett?
Most gate repairs in Everett fall between $200 and $600, and the number depends on the fault and the system. A typical driveway gate repair runs $200 to $600 depending on whether it’s a hinge, a roller, or a control issue. Sliding gate repair is similarly $200 to $600, while commercial gate repair runs $300 to $900 because the operators are heavier and the access control adds diagnostic work. Gate welding adds $150 to $450 depending on the size of the structural repair.
Several things move the price: the brand and grade of the operator, whether the fault is mechanical or electrical, and how much realignment is needed to make the fix last. You avoid overpaying when the diagnosis is right the first time, which is why we test the operator and the gate separately rather than swapping parts and hoping. Repair versus replacement is a real decision, and we’ll tell you which one actually makes sense for your gate instead of defaulting to the more expensive option.
Our estimate is free, and every price is quoted and agreed before any work starts. You’ll know the cost up front, and that agreed price is what you pay. Call (844) 834-1197 for a free estimate and we’ll get you scheduled.
Our Service Area Near Everett
We serve Everett and the surrounding communities, including Eastmont, Snohomish, Mukilteo, Lake Stickney, Mill Creek, Silver Firs, Martha Lake, North Lynnwood, and Mill Creek East. Response times vary by location and how busy the day is, so call early for the best chance at same-day service. If you’re nearby and need gate repair, we can point you to the right local page. For a broader look at what we cover, see our main Gate Repair Everett page. Fast dispatch from 7am to 7pm, Sunday through Friday. For electric faults specifically, our gate repair team handles the controls, motors, and boards. Neighbors in Snohomish can reach us through gate repair as well.
Serving Everett, WA – Our Local Coverage Area
We serve Everett and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Everett
Gate repair is the work of diagnosing and fixing the mechanical and electrical faults that stop an automatic gate from opening, closing, or latching properly. It covers the operator, the hinges, the track or swing path, the control board, the sensors, and the access hardware. At Gate Repair Everett, we test the operator and the gate separately so we fix the real cause instead of guessing. Call (844) 834-1197 for a free estimate.
Most gate repairs are completed in a single visit, often within a couple of hours once the fault is identified. Simple fixes like a worn roller, a reset limit switch, or a hinge adjustment are quick, while structural welding or access-control diagnostics can take longer. We’ll tell you what to expect after the on-site diagnosis. Call (844) 834-1197 to get scheduled.
Most gate repairs in Everett run $200 to $600, with commercial systems at $300 to $900 and gate welding at $150 to $450. The exact price depends on the fault, the operator brand, and how much realignment is involved, and it’s all set by the written estimate. We agree on the price before any work starts, so there are no surprises. Call (844) 834-1197 for an exact quote, and estimates are free.
Yes, we work on the brands you already own, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians recognize model-level failure patterns across these systems, which speeds up diagnosis. We’re fluent in both residential and commercial operators. Call (844) 834-1197 and tell us what brand you have.
Same-day service is often possible when you call early in the day, depending on the fault and the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (844) 834-1197 and we’ll find the soonest opening for you.
We confirm warranty terms with you before work begins, and the details are set out in your written estimate. We stand behind the repairs completed and will address any issue that comes up with the work. Call (844) 834-1197 and we’ll answer your questions about coverage.
Clear access to the gate on both sides so our technicians can inspect the full travel, and have any remotes, keypads, and codes ready to test. Jot down what the gate does, whether it’s the open or close that fails, and what brand the operator is. That information helps us diagnose faster. Call (844) 834-1197 to schedule.
Schedule Your Gate Repair Service in Everett Today
Don’t let a stuck or failing gate cost you another day of parking on the street. Gate Repair Everett works on the brand you already own and tells you honestly whether a repair or replacement makes sense, with a free, no-obligation estimate before anything starts. Call (844) 834-1197. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Everett.