Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Everett Homeowners
A new gate is a big purchase, and the failure we see most often isn’t a bad gate: it’s a good gate mounted on a poor footing, driven by an operator sized for the wrong leaf. It works fine for a season, then the sag, the grinding, or the phantom stops start. We’re a gate specialist, not a general contractor or a garage-door company that dabbles. Our technicians have up to experience across residential and light-commercial swing, slide, and barrier arm systems, and we work on the brand you already own. Gate installation work in Everett is measured and scheduled rather than same-day, so you get a free on-site measure and a written price before anything is ordered. Call (844) 834-1197.
Automatic Gate Installation
Automatic Gate Installation is the package that makes a driveway entrance open on its own: the gate, the operator, the safety devices, and the access control working as one system. You need it when a manual gate has become a climb-out-every-time chore, when you’re replacing an aging operator that no longer has parts support, or when a property needs controlled entry rather than an open drive. We survey the site, match the operator to the weight and length of the leaf, and install it as one finished system. Typical automatic gate installation in Everett runs roughly $3,200 to $7,500 depending on leaf size, operator class, and how much site work the entrance needs. The written estimate sets the final price, and the price is agreed before any work starts.
Operator Selection and Sizing
An undersized operator is the most common cause of early failure on an automatic gate. We weigh the leaf, check the travel distance, and match the duty cycle to how often the gate will actually run each day.
Safety Devices and Sensors
Photo eyes, safety edges, and proper obstruction sensing are wired and tested before the gate is handed over. On a heavy moving panel, those devices are not an add-on: they’re the part that keeps a person or a vehicle out of harm’s way.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Installation Services
Gate Installation Services cover the full job from layout to first cycle: setting or building the mounting points, hanging or tracking the gate, mounting the operator, wiring power, and programming the entry controls. We offer them when a property is going from no gate to a gated entrance, when an existing gate is being replaced with a larger or heavier one, and when a homeowner is tired of patching a unit that keeps failing. We handle swing, slide, and barrier arm configurations for homes, HOAs, and small commercial properties under one roof. Most residential projects land in the $2,400 to $6,800 range depending on gate width, material, and operator. We quote the whole job in writing first, so there’s no invoice surprise at the end.
Residential and Light-Commercial Jobs
The distinction matters for duty cycle and access control. A home drive gate might cycle a dozen times a day; an HOA entrance or a commercial lot cycles constantly, and the operator has to be built for that.

Retrofit and Upgrade Projects
Sometimes the frame and panels are sound and only the drive side is tired. We assess whether new automation on the existing gate makes sense, or whether a replacement will serve you better.

Electric Gate Installation
Electric Gate Installation is the electrical side of the job: bringing power to the gate location, wiring the operator, connecting the control board, and integrating keypads, remotes, or entry systems. We specify it whenever a gate will be automated with anything beyond a simple push-button, and on every commercial or shared entrance where access has to be managed rather than just opened. Our electric gate repair work is a core specialty, which is exactly why our installs are wired cleanly the first time. Typical electric gate installation in Everett runs about $3,500 to $8,200 depending on the power run, the operator, and the access control you choose. The estimate is free and written, and no work starts until you’ve agreed to it.
Power Runs and Control Wiring
Power and control wiring are only as good as their routing and their connections. We plan the run before the trenching, keep low-voltage control wiring separated from line power, and label the board so the next person in the box can read it.
Access Control Integration
Keypads, telephone entry, and remote receivers all tie into the same control board, and the order matters. We commission each device and test every credential before we consider the job finished.
Driveway Gate Installation
Driveway Gate Installation is a gate sized and placed for the way vehicles actually come and go on your property, including the swing clearance, the approach, and where the driveway meets the street. You need it when a new drive is being gated for the first time, when a narrow or short entrance keeps clipping mirrors, or when the existing gate was installed too close to the curb for a longer vehicle to clear. We walk the drive, check turning paths, and set posts to proper footing depth before anything is built on them. A typical driveway gate install in Everett runs roughly $2,800 to $7,000 depending on width, material, and whether the entrance is automated. Price is confirmed on the written estimate before we begin.
Swing Clearance and Approach
A gate can be perfectly built and still be wrong if the swing arcs into the drive or blocks a parked car. We check the arc against the vehicles that will actually use it, not against a generic chart.
Heavy Panels and Footings
A wide driveway gate is heavy, and the footing carries that load every time it moves. Posts set to proper footing depth on a level base are what keep the gate swinging true instead of dragging within a year.
Sliding Gate Installation
Sliding Gate Installation is the right answer when a driveway is short, sloped, or too tight for a swing gate, or when a property wants a gate that opens flat along a fence line instead of into it. We recommend it for narrow entrances, steep approaches, and sites where a swing leaf would foul a parked car or a structure. The install covers the track, the guide rollers, the operator, and the safety edges, and the geometry has to be right from the start or a slide gate will wander off track. Typical sliding gate installs in Everett run about $3,000 to $7,800 depending on span, material, and operator. The written estimate is free and the price is set before work starts.
Track and Roller Geometry
Track level and roller alignment decide whether a slide gate runs quietly for years or shudders and jumps within a season. We set the track on a proper base and confirm travel in both directions before powering anything up.
Keeping the Gate on Its Track
A slide gate that has come off its track is heavy and dangerous to handle, so we don’t recommend trying to lift one back into place yourself. We bring the equipment and the training to reset it safely.
Gate Opener Installation
Gate Opener Installation is the automation half of the project: choosing the operator, mounting it to the post or frame, wiring it, and setting the travel limits and reversal sensitivity. You need it when you’re automating a manual gate for the first time, replacing a failed opener on an existing gate, or upgrading to something that can handle more cycles or better access control. We work across the major operator brands, from consumer-grade units to professional access control hardware, and we match the actuator to the gate rather than the other way around. Typical gate opener installation in Everett runs roughly $1,800 to $4,600 depending on operator class and whether power is already at the gate. The estimate is written and agreed before any work begins.
Operator Matching
The opener has to be rated for the weight of the leaf and for how often it will cycle. Getting that wrong is the usual reason a perfectly new operator fails early, no matter the brand.
Limits and Reversal Testing
Travel limits and reversal sensitivity are set by hand and then tested repeatedly. An operator that reverses too late on contact is not safe, and an operator that reverses on a leaf of wind is not usable.
Gate Fabrication
Gate Fabrication is the custom side of the work: building a gate to fit an entrance that no stock panel will fit, or matching a design a property already uses elsewhere. It comes up on odd-width drives, on sloped or angled openings, on HOAs that need a consistent look, and on gates where the existing frame is sound but the panels are past replacing individually. We take measurements on site, work out how the leaf will be built, and coordinate the fabrication with the install so there’s no gap between what arrives and what fits. Custom fabrication in Everett generally runs about $2,000 to $6,500 depending on size, material, and design detail. We quote it per job in writing, and nothing is made until you’ve approved that figure.
Custom Sizing for Odd Openings
An angled or variable-width entrance needs a gate built to those measurements, not a stock panel shimmed into place. Getting the dimensions right the first time is what prevents the gate from racking later.
Matching Existing Style and Materials
If there’s already a fence or a gate on the property, the new one should look like it belongs there. We note the proportions, rails, and finish details before fabrication starts.
Brands We Service
We service Linear equipment and know where it wears out, especially the drive components and control board connectors that get the most cycles. Linear operators are common on residential driveway entrances around Everett, and their failure patterns are familiar to us. We also service Viking operators, including the swing and slide units that have been on gates for years and still work fine with the right attention to their limits and safety devices.
Ghost Controls is another brand we work on regularly, and its control boards reward careful wiring and correct limit settings. For commercial and shared entrances, we’re experienced with DoorKing access control hardware and understand how the entry systems tie into the operator. Those four are a slice of what we see; we work on LiftMaster, FAAC, BFT, Elite, and Mighty Mule as well. Whether you have Linear, Viking, Ghost Controls, DoorKing, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- A gate that needs a push to start moving. When the leaf sags or the track is off, the operator has to drag it through every cycle, which wears the drive and the motor faster. It’s usually a small adjustment now and a bigger job later if it’s left.
- Reversal that’s slow or missing. A safety device that doesn’t stop and reverse the gate on contact needs attention before the gate is used again. Test it on a regular basis with something soft and light, standing clear of the leaf.
- A grind, clunk, or squeal on every cycle. Noise from the operator or the gate hardware usually points to a worn component or a misaligned track. Catching it early keeps one worn part from taking others with it.
- The gate stops partway and reverses. Often this is a limit setting, a binding leaf, or a control board fault rather than a dead motor. Diagnostic work tells you which, so you’re not replacing good hardware.
- A panel or post that has shifted. Heavy gate panels and sagging posts can come down or jam in a way that traps a vehicle or a person. Don’t try to shift a heavy gate back into place yourself; that’s worker territory.
Our Process, Step by Step
- 1
Call and describe the entrance. Tell us the driveway width, whether it’s a swing or slide gate, and what’s already on site. We’ll book a time for a free on-site measure, and this is where a fresh install or replacement starts.
- 2
On-site measure and site review. We check the approach, the swing or track geometry, and where power could run. We ask about how often the gate will cycle, since that decides which operator class you actually need.
- 3
Written estimate and plan. You get a written price before anything is ordered. It lists the gate, the operator, the safety devices, and the access control, so you can see what’s included.
- 4
Installation. We set posts and track to proper footing depth, hang or track the gate, mount the operator, and wire everything through to the control board. We test the travel and reversal settings on every cycle before we call it done.
- 5
Handover and walkthrough. We show you how to operate and test the gate, how to cycle the safety devices safely, and what to check if something feels off. If the gate ever acts up later, we handle electric gate repair as well as new installs.
How Much Does Gate Installation Cost in Everett?
Gate installation in Everett generally runs $1,800 to $8,200 depending on the scope, and it’s worth thinking about the job in realistic scenarios. A typical gate opener install runs $1,800 to $4,600 depending on the operator class. A full driveway gate with automation typically lands in the $2,800 to $7,000 range. A sliding gate installation typically runs $3,000 to $7,800, and a fully automated swing entrance generally falls between $3,200 and $7,500. Custom fabrication is quoted per job, and a full electric install with access control generally sits in the $3,500 to $8,200 range.
The factors that move the number most are the size and weight of the leaf, the material, the operator duty cycle you need, and how far the power has to travel to reach the gate. A short run to an existing outlet is cheaper than trenching power across a yard. Avoiding overpayment is mostly about getting the operator sized correctly from the start and not buying automation you don’t need for a gate that cycles a dozen times a day. Every free estimate includes a site measure, a walk through the power and control plan, and a written price with the gate, operator, safety devices, and access control itemized. The price you agree to is the price you pay, and no work starts until you’ve accepted it in writing.
Our Service Area Near Everett
We serve homeowners and property managers across our Everett service area and the surrounding communities, including Eastmont, Snohomish, Mukilteo, Mill Creek, Silver Firs, Martha Lake, Lake Stickney, North Lynnwood, and Mill Creek East. Installation visits are scheduled in advance so the measurement, the ordering, and the install line up without gaps. If you’re not sure whether your gate is in our range, call (844) 834-1197 and we’ll tell you quickly. We also handle gate repair if your current gate needs service first.
Serving Everett, WA – Our Local Coverage Area
We serve Everett and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in Everett
Gate installation is the process of building or mounting a new gate and, if it will be automated, fitting the operator, safety devices, and access controls that drive it. It covers the site measure, setting the posts or track to proper depth, hanging the gate, wiring the operator, and testing the full system. The goal is a gate that opens reliably and reverses safely on contact. To start the process in Everett, call (844) 834-1197 for a free estimate.
Most residential gate installs in Everett take one to two days on site once the gate and operator are on hand, and larger automated or sliding systems can take longer. Custom fabrication adds time before the install, because the panel is built to your dimensions first. The written estimate gives you the expected timeline before anything is ordered. Call (844) 834-1197 to get measured and get a schedule.
Gate installation in Everett generally runs $1,800 to $8,200 depending on the size, materials, operator class, and access control. A simple opener install sits near the low end, while a full automated swing entrance or an electric install with access control sits near the top. The written estimate sets the final price, and it’s free. Call (844) 834-1197 for an exact quote, and estimates are free.
Yes, we install and service Linear and DoorKing equipment, along with Ghost Controls, Viking, LiftMaster, FAAC, BFT, Elite, and Mighty Mule. We’re independent and experienced with each brand, so we can match the operator to your gate rather than pushing a single make. We’ll tell you honestly if your existing hardware is worth automating. Call (844) 834-1197 and tell us what you have.
No. Gate installation is a measured and scheduled job rather than same-day work, because the gate and operator are ordered to fit your entrance. We answer 24/7, and fast dispatch from 7am to 7pm Sunday through Friday covers the initial measure and any service calls. A call outside dispatch hours is booked into the next opening. Call (844) 834-1197 to book your free measure.
Warranty terms are confirmed with you in writing as part of your estimate, so there’s no ambiguity about what’s covered and for how long. Manufacturer coverage on the gate and operator varies by brand and by the model we specify. We put the details in the estimate before any work starts. Call (844) 834-1197 and we’ll walk you through what’s included.
Clear the approach to the driveway and the gate area so the technicians can measure and work safely. Make sure vehicles can be parked clear of the swing or track path for the day. Have the property’s power access point available for the on-site measure. To set up the visit, call (844) 834-1197. We answer 24/7.
Schedule Your Gate Installation Service in Everett Today
Ready to stop climbing out to open a gate? Call (844) 834-1197 for a free on-site measure and a written price for your gate installation in Everett. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, covers the initial visit. You’ll get an honest read on what’s needed, a clear estimate, and no obligation to proceed.
Written by the team at Gate Repair Everett.